KXF-W4030CT-405STEREO CASSETTE TAPE DECKB60-4536-08 (EN)KENWOOD CORPORATIONINSTRUCTION MANUAL
10Playback (recording) preparation2Select the tape transport direction.1Load a cassette tape in deck A or B.Preparation for playback (recording)Before
11Listening to cassette tapeNormal playbackListening to cassette tapesPreparationMake “Playback (recording) preparation”.0Zero-stop operationTo play s
12Listening to cassette tape÷Tapes are played in the directions indicated by their respective indica-tors on the display.÷The playback starts with the
14Convenient music search (DPSS)Skip play operationTo play the tune located 4 tunes behindConvenient music search (DPSS)The DPSS (Direct Program Searc
15Convenient music search (DPSS)Single-tune repeated playback operation÷Normal playback resumes after repeating the same tune for 16 times.÷Press t
16How to record (Deck B only)Each press of the MODE key changes the setting.1 “LEVEL” lights up: Recording level setting mode2 “BAL.” lights up: Recor
17How to record (Deck B only)÷Recording will start.÷The deck enters the stop mode automatically when the tape hasbeen recorded till the end.Press once
18How to record (Deck B only)To stop recordingIn stop modeDuring recordingPauseTo pause recording temporarilyHow to provide non-recorded blanks betwee
19Perform auto-bias adjustment. (The bias adjustment is applied to deck B.)Tape dubbing operation (Deck A \ Deck B)To stop dubbingPress the stop (7) k
2Introduction*AC voltage selectionThe AC voltage selector switch on the rear panel is set to thevoltage that prevails in the area to which the unit is
20Start playing the CD.Set the record-pause mode.Adjust the recording level.2Press 7 key of theCD player.Press the 6 keyof the CD player.1 Play a CD.
21Recording of CD playback (CCRS) (Deck B only)1Insert a tape in deck B.2Determine the recording condition.1Select the recording mode.3When connected
22÷Set the timer so that the tape starts at the desired time of the day.÷When the set time comes, tape playback starts automatically.÷Read carefully t
2334Set the TIMER switch to REC.Set the amplifier volume to the minimum position.÷Refer to the "How to use the MPX FILTER key". &÷To can
24In case of difficulty÷Please note that resetting microcomputer clears contentsstored inand returns it to the condition when it left the factory.What
In case of difficulty25÷Use a cassette with unbroken tab or close thehole.÷Close the cassette holder completely.÷Adjust the recording level referring
26Dolby noise reduction systemThe Dolby noise reduction system was developed to reduce the tape hiss noise generated during playback.The optimum effec
27Track System ... 4 track, 2 channel stereoRecording System ... AC bias (Frequency: 105 kHz)Heads ...
For your recordsRecord the serial number, found on the back of the unit, in the spacesdesignated on the warranty card, and in the space provided below
3AccessoriesCheck that the following accessories are present.Audio cord ... (2) System control cord ... (1)AC plug adapt
4Caution on condensationCondensation (of dew) may occur inside the unit when there is a greatdifference in temperature between this unit and the outsi
5To store cassette tapesDo not store the tapes in a place which is subject to directsunlight, or near equipment that generates heat. Keep thecassette
6LINE INREC PLAYLINE OUTSYSTEM CONTROLLR1234567890 +100764¢1¡PHONOTAPEREC PLAYLRSIGNAL GNDRLSYSTEMCONTROLSYSTEMCONTROL1. Connect all cords firmly.
7SYSTEM CONTROL OPERATIONSRemote ControlLets you operate this unit with the system remote control unit supplied with the amplifier or receiver.Automat
8TAPE AAUTO REVERSETAPE BAUTO REVERSEPOWERPHONESTIMER PLAYREC OFF PLAYMODEREC LEVEL/BAL/BIAS- ON – OFF1237¡ 1 ¡8PAUSE ¶REC/ARM0237RESET AMIN/L MAX
91 Deck AThis deck is used exclusively for play-back.2 Deck A eject (0) key 0Press to open the cassette holder ofdeck A.3 Deck B eject (0) key 0Press
Comentários a estes Manuais