Kenwood CCD-2000 Manual do Utilizador descarregar pdf (Página 3)

English

Installation Procedure

1. To prevent a short circuit, remove the key from

the ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wiring harness wires in the following

order: ground, ignition, reverse and camera unit.

4. Connect the wiring harness connector to the

video box unit.

5. Install the unit in your car.

6. Reconnect the - battery.

2WARNING

• If you connect the ignition wire (Red) to the car chassis

(Ground), you may cause a short circuit, that in turn may

start a fire. Always connect those wires to the power

source running through the fuse box.

• Do not cut out the fuse from the ignition wire (Red). The

power supply must be connected to the wires via the

fuse.

2CAUTION

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that can be

turned on and off with the ignition key. If you connect the

ignition wire to a power source with a constant voltage

supply, as with battery wires, the battery may die.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not remove

the caps on the ends of the unconnected wires or the

terminals.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Install so that it does not obstruct the rear field of view.

• Install so that it does not protrude from the side of the

car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which the unit

is to be attached before installing.

• Moisture on the attachment surface reduces adhesive

strength, which may lead to the unit coming off.

• Do not attach the camera bracket to areas on the car

body treated with fluorocarbon resin, or glass.

• May result in the rear view camera falling off.

- Do not apply water to the unit.

- Do not expose the unit to rain.

- Do not subject the camera to unnecessary force.

- Thoroughly clean where tape is used for sticking on

the unit.

• Refer to the Instruction’s manual for details on connecting

the other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape.

To protect the wiring, wrap adhesive tape around them

where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and seat

rails.

• Do not route wiring in places that get hot, such as near

the heater outlet. If the insulation of the wiring melts or

gets torn, there is a danger of the wiring short-circuiting

to the vehicle body.

• When replacing the fuse, be sure to use only fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA cable as far away from each other

as possible.

• Do not install the video box unit in places where it may

become subject to high temperatures or humidity, such

as:

- Places close to a heater, vent or air conditioner.

- Places exposed to direct sunlight, such as on top of the

dashboard or the rear shelf.

- Places that may be splashed by rain, for example close

to the door.

B64-3673-00_English.indd 3B64-3673-00_English.indd 3 07.2.2 11:13:48 AM07.2.2 11:13:48 AM

1 2 3 4 5 6 7

Comentários a estes Manuais

Sem comentários

Kenwood CCD-2000 Manual do Utilizador Página 3

Comentários a estes Manuais

Manuais e produtos relacionados com Multimédia Kenwood CCD-2000